4 г. назад
Choufli 7all S3 / 2007 http://www.youtube.com/playlist?list=PLw8jJpUmkhrfcMysdpWoberfAGWE9twpO Choufli 7all S4 / 2008 https://www.youtube.com/playlist?list=PLw8jJpUmkhrdBSw1mwJ_Z577CnofvqoJl Choufli 7all S5 / 2009 https://www.youtube.com/playlist?list=PLw8jJpUmkhreZAksYg-ZUMd7SFCK7XNIT Choufli 7all S1 / 2005 http://www.youtube.com/playlist?list=PLw8jJpUmkhrcFW4uE4H6M-VbI0G8gci2Y Choufli 7all S2 / 2006 http://www.youtube.com/playlist?list=PLw8jJpUmkhrdl2p6trJkG3ZqlPpNuy9C- SUBSCRIBE : https://www.youtube.com/BenzavisionTV
12 мес. назад
Studio de Dublagem:https://www.youtube.com/user/YouDubbing Confiram o canal da Dublagem(São Excelentes), Edição GTV Fiquem com Deus Resident Evil 4 - O Filme Dublado HD 2016 (Resgate de Ashley)
6 г. назад
Buy Ball Joints Here: http://www.jeepswag.com/jeep_jk_ball_joints/index.html Dominion Offroad Jeep JK products available at www.JeepSWAG.com If you like this vid, click the "Like" button Specialty tools used: - Harbor Freight "Four Wheel Drive Ball Joint Service Kit" - 2" long X 1.25" piece of pipe. (I'm sure that 1.5" diameter would work too) - 1.5" - 1.75" OD washers (I used four thick ones) - Small piece of 1/8" thick steel to use as a spacer. I used a thick washer. - 21mm socket for caliper bolts - 35mm socket for the axle nut - 12 point 13mm closed end wrench - Torque wrench - might need a pickle fork - A small box that's strong enough to support the weight of the brake disk and caliper (8" - 12" tall) - All other required tools are fairly common. Here's the order of events. (not very useful when taking it apart, but will most likely save some frustration when putting it back together) Removal: 1. Remove wheel and clean the working area. A pressure washer works great. 2. Remove the two 21mm caliper bolts and place the brake disk and caliper on the box 3. Remove the speed sensor 4. Remove 3 12 point 13mm bolts, axle nut, unit bearing and axle shaft 5. Remove ball joint cotter pins and castle nuts 6. With the 2" piece of pipe and washers, press out the upper ball joint 7. Press out the upper ball joint 8. Press out the lower ball joint I could have save a lot of time, by printing out the following and keeping it next to me during the install Installation: (this assumes that you will torque all fasteners to spec and use thread locker when required) 1. Press in the lower ball joint 2. Install zerk fitting if applicable 3. Using the 1/8" spacer, press in the upper ball joint 4. Install Zerk fitting if applicable 5. Install the grease boots (do not grease yet) 6. Using the lower ball joint castle nut, place the knuckle in position 7. Place the speed sensor wire holder, in place on the upper ball joint and install the upper castle nut 8. Torque the castle nuts to spec and install cotter pins 9. Grease the ball joints if applicable 10. Install axle 11. Run the speed sensor wire through and install the dust cover, unit bearing and axle nut 12. Install the speed sensor 13. Install the brake disk and caliper... If you like this vid, click the "Like" button
7 г. назад
http://www.wellsve.com/ This video demonstrates how to diagnose a sticky poppet injector utilizing scan tool and 5 gas techniques. The upper and lower intake are removed and replaced. The distributor cam sensor retard is re-synced using a scan tool. The re-sync also needs to be performed at times when a P0340 trouble code sets. The information presented in this program is based on a specific diagnostic case and might not directly apply to the vehicle you are repairing. We do not represent or warrant that the information presented is complete or error free. Please take all safety precautions. We disclaim any and all liability for losses, injuries or damages in connection with your repair.
2 мес. назад
Today we tackle 3 different acts -- Logbox 720 Act 3, and the first 2 acts of a new game world! ▄▀■ *SUPPORT ME ON PATREON!* ■▀▄ ► http://www.Patreon.com/Scykoh ▄▀■ *FOLLOW MY CRUD!* ■▀▄ ► Twitter: http://www.Twitter.com/Scykoh ► Live Stream: http://www.Twitch.tv/Scykoh ▄▀■ *OTHER CHANNELS* ■▀▄ ► Main Channel: http://www.YouTube.com/Scykoh ► Random Stuff Channel: http://www.YouTube.com/ScykohCrud
1 г. назад
Countdown to Dark Souls III Week 3: Dark Souls Starter Guide Mechanics intro @ 00:43 Poise @ 1:49 Equip Burden @ 2:50 Stability @ 4:38 Weapon Scaling @ 5:43 Attuning Spells @ 6:23 Humanity, Hollowing, Death and Online @ 7:27 Equipment @ 14:55 Classes + Starting Gift @ 16:40 Weapons @ 19:12 Dark Souls Class Guide: https://youtu.be/-mol2q0XBAw ►Follow on Twitter for notifications on new vids: http://bit.ly/silvermonttwitter ►Silver Mont Patreon page: http://bit.ly/MontPatreon ►Paypal Donations http://bit.ly/MontPaypal ►Channel Artist's Web-store http://rdbl.co/1WUutgl ►The official Silver Mont Steam Group: http://bit.ly/silvermontsteam
4 г. назад
How to fix rough idle mustang 4.6. Mass Air Flow Sensor Cleaning, IAC Valve, Replace Coil Packs.